女人下边被添全过视频的网址,麻豆网站少妇AAA片,亚洲精品 无码一区二区三区 ,少妇人妻无套进入69va
Hello, Welcome to Jinan Fast CNC Machinery Co.,Ltd!

CONTACT INFO

JINAN FAST CNC MACHINERY CO., LTD


WhatsApp:086-15098878331

Mobile: 086-15098878331 

E-mail: chelsea@fastechcnc.com

              lfqft@163.com

Fax:086-0531-87459135

Add: No 8521 WEST JIGSHI ROAD, JINAN.CHINA

Zip:250300



CNC plane drilling - the use of drill bit details

Source: Time:2017-06-24 13:55:06 views:

⒈ bit should be installed in a special packaging box, to avoid vibration collide with each other. CNC plane drilling ⒉ use, remove the drill from the box should be installed into the spindle collet chuck or automatically replace the bit tool magazine. Use it back into the box.
⒈ bit should be installed in a special packaging box, to avoid vibration collide with each other. CNC plane drilling
⒉ use, remove the drill from the box should be installed into the spindle collet chuck or automatically replace the bit tool magazine. Use it back into the box.
⒊ Measuring the diameter of the drill Use a non-contact measuring instrument such as a tool microscope to prevent the cutting edge from colliding with the mechanical measuring instrument.
⒋ Some CNC drilling machine use the positioning ring Some CNC drilling machine does not use the positioning ring, such as the use of fixed ring installation of the depth positioning must be accurate, such as the use of the positioning ring drill bit installed on the spindle to adjust the elongation of consistency , Multi-spindle drilling more to pay attention to this point, to make each spindle drilling depth to be consistent. If inconsistent it is possible to drill bit to the table or can not drill through the circuit board scrapped.
⒌ Usually 40 times the stereo microscope can be used to check the drill cutting edge wear. CNC plane drilling
⒍ Always check the concentricity of the spindle and collet chuck and collet chuck clamping force, poor concentricity will result in small diameter drill broken drill and large aperture, the clamping force is not good will cause the actual speed and settings The speed does not meet, between the chuck and the drill slip.
⒎ fixed handle drill chuck in the collet chuck length of 4 to 5 times the diameter of the drill handle to clamp.
⒏ Check the spindle presser frequently. The presser foot contact surface should be horizontal and vertical to the spindle can not be shaken, to prevent the drill cut and cut holes.
⒐ Drilling machine's vacuuming effect is better, vacuuming can reduce the bit temperature, while taking away the dust to reduce friction to produce high temperature.
⒑ The substrate stack includes top and bottom backing plates to be positioned and flattened in a hole-and-slot positioning system on the table of the drilling machine. The use of adhesive tape to prevent the drill bit drilling tape stuck to the drill bit chip, resulting in chip removal difficulties and broken drill.
⒒ order manufacturer's drill, factory inspection to sampling 4% of its compliance. And 100% with 10 to 15 times the microscope to check its nicks, abrasions and cracks.
適 timely re-grinding bit can increase the use of bits and the number of resharpening, drill bit life to extend and reduce production costs and costs. Usually measured by a tool microscope, the depth of wear should be less than 0.2 mm over the full length of the two main cutting edges. When grinding to wear to 0.25mm. Ordinary shank drill bits can be resized three times and undercut bits can be resharpened two times. Turning over the hole quality and precision of its drilling will decline, will result in scrapped PCB products. Overturn effect is counterproductive. CNC plane drilling
鉆 When due to wear and its wear diameter is reduced by 2% compared with the original, then the drill scrapped.
⒕ bit parameter settings Under normal circumstances, the manufacturer provides a production of the drill bit drilling speed and speed parameters table, the parameter is only a reference, in fact, but also the actual use of the craft to come up with a realistic In case of bit speed and speed parameters, usually the actual parameters and reference parameters are different but not too much difference.
⒖ bit sharpening, should try to twist the two major cutting edge grinding symmetry, so that the two main cutting edge of the radial force offset each other to prevent bit deflection and aperture expansion. CNC plane drilling
keys: 
Links
       
MOBILE STATION SCAN

     WeChat SCAN
TEL:086-15098878331   FAX:086-0531-87459135   Mobile:086-15098878331
ZIP:250300    Email:chelsea@fastechcnc.com
ADD:NO 8521 WEST JINGSHI ROAD JINAN,CHINA
Copyright© Jinan Fast CNC Machinery Co., Ltd
亚洲AV无码专区一级婬片毛片 | 午夜视频在线免费观看 | 91绿奴人妻一区二区 | 少妇做爰免费5级A片 | 50露脸__X88AV| 经典媚黑国产精品合集 | 日韩成人无码电影网站 | 亚洲人妻在线视频 | 美女的胸 又黄 又大jk网站 | 人妻熟女aⅴ一区二区三区汇编 | 亚洲AV成人无码久久精品专区 | 蜜臀99久久精品久久久久久软件 | 免费观看无码视频 | 成人无码www免费视频网站软件 | 国产香蕉精品视频 | 人妻AⅤ中出‘‘无码内射 一级a一级a爰片免费视频 | 少妇人妻偷人精品无码视频九色 | 无码人妻精品一区二区中文 | 蜜桃av秘 无一区二区三区、 | 久久精品人妻一区二区三区蜜桃 | 一级a一级a爰片免费免免水网 | 少妇做爱xxxⅹ高潮片入口 | 【無碼破解版】 在线 | 欧美乱码精品一区二区三区 | www.av在线| 无码人妻一区二区三区精品不付款 | 亚洲无码国产中文字幕三上悠亚 | 精品无码一区二区在线蜜桃 | 特级西西www大胆无码视频 | 免费看人妻换人妻互换A片爽 | 国产一级婬片久久久片A级 国产精品一级毛片在码A片 | 亚洲AV无码乱码A片秀色直播 | 一级做a爱片毛片A片动漫app | 少妇搡BBBB搡BBB搡澳门 | 国产熟女盗摄一区二区警花91 | 护士性做爰A片免费看 | 国产高潮A片羞羞视频涩涩 农村A片婬片AAA毛片 | 五月激情综合美女久久 | 特级西西444WW大胆视频 | 国产高清无码视频在线观看 | 狠狠色噜噜狠狠狠888米奇视频 |